• 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • ,
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor

    • $375.00
    • *Allows for one pass cuts on cylinder heads. *Choice of an  R-8 Adaptor for use with a Bridgegport-type Mill or a 1" Stub Arbor to be held in an end mill holder. *The flycutter NOW comes with a REPLACEABLE  Carbide Insert Tool Holder.  One insert for Cast Iron and one insert for Aluminum heads are included.  Additional inserts (specify cast…
    • Order Online
  • A B EPOXY Quick View
    • A B EPOXY Quick View
    • ,
    • A B EPOXY

    • $30.00
    • This is the good stuff. Works great on intake runners and manifolds. Molds like clay and maintains the formed shape without sagging or running. Stays where you put it ~ gas or alcohol doesn’t hurt it. Sets up harder than Superman’s Head in about 3 hours, yet machines very well. Forget the exhaust ports ~ it lasted 3 pulls on…
    • Call To Order
  • ADJUSTABLE PUSHROD Quick View
    • ADJUSTABLE PUSHROD Quick View
    • ,
    • ADJUSTABLE PUSHROD

    • $35.00
    • *Fits both cup & ball type rocker arms *Eliminates trial and error fittings ~a must for making correct length pushrods *Simply adjust pushrod length to yield desired rocker arm geometry, measure sample and cut length correctly the first time
    • Call To Order
  • Alignment Tool for Bridgeport-Type MillAlignment Tool for Bridgeport-Type Mill Quick View
  • Ball Micrometer 0 to 1” Quick View
    • Ball Micrometer 0 to 1” Quick View
    • ,
    • Ball Micrometer 0 to 1”

    • $120.00
    • This is what you use to mike bearings. It is common knowledge that all bearings are not the same thickness. By juggling bearing thickness, a lot of clearance problems can be eliminated. * .0001 Graduation * Carbide Faces (Anvil & Spindle) * Wrench Included for Quick Zero Adjustment
    • Call To Place Order
  • BEARING DRIVER Quick View
    • BEARING DRIVER Quick View
    • ,
    • BEARING DRIVER

    • $50.00
    • This fixture enables you to install the pinion support bearing on a 9" Ford without killing the race. Made of ALUMINUM Steel driving ring Anodized for appearance and durability Enhances the installation of a ring and pinion Give Us A Call To Order Now.
    • Order Online
  • Bellhousing Indexing FixtureBellhousing Indexing Fixture Quick View
    • Bellhousing Indexing FixtureBellhousing Indexing Fixture Quick View
    • ,
    • Bellhousing Indexing Fixture

    • $75.00
    •   This is the tool that is often over-looked when installing a manual transmission.  It is also the tool that is responsible for a clean releasing clutch and smooth shifting.   Believe me, not ONE scattershield made is concentric with the crankshaft as they come from the factory.  All of them must be indicated and adjusted for proper alignment and…
    • Purchase on Ebay store
  • Blank Aluminum Chuck Jaws Quick View
    • Blank Aluminum Chuck Jaws Quick View
    • ,
    • Blank Aluminum Chuck Jaws

    • $150.00
    • * In stock for popular chucks * Bolt jaws on in place of permanent jaws * Machine in place for perfect accuracy and concentricity * A must for holding pistons while cutting ring grooves or facing flat tops * Spiders also available * Complete instructions Specify exact chuck specs including: Make, Model No. & Size
    • Call To Place Order
  • BLOCK & HEAD HANDLES Quick View
    • BLOCK & HEAD HANDLES Quick View
    • ,
    • BLOCK & HEAD HANDLES

    • $45.00
    • These simple little tools take a lot of work out of handling and transporting heads, blocks or entire engine assemblies. Simply thread into any 3/8” 16 tpi bolt hole and you have an instant handle. NOTE: Be sure to screw handles in flush with block/head to prevent bending screws.   Set includes: 4 aluminum handles Heat-treated ~ 8 3/8” 16…
    • Call To Place Order
  • BLOCK DECK HEIGHT GAUGE Quick View
    • BLOCK DECK HEIGHT GAUGE Quick View
    • ,
    • BLOCK DECK HEIGHT GAUGE

    • $200.00
    • This is what you use to assure all four corners of your block are the same distance from the crankshaft. Remember, all the work on center to center rod length, piston compression height, and correcting the crank stroke, are out the window if your block isn't square. The tool can also be used for actual measurement if set with a…
    • Order Online
  • BLOCK MOUNTED INDICATOR FIXTURE Quick View
    • BLOCK MOUNTED INDICATOR FIXTURE Quick View
    • ,
    • BLOCK MOUNTED INDICATOR FIXTURE

    • $75.00
    • This fixture is perfect for degreeing a camshaft because when the unit is screwed into the deck surface, the stem of the indicator is always parallel to the lifter bores. * Tool is machined & black anodized * Complete with 5” extension for reaching down to filter *1/2” & 7/16” threaded shaft fits most blocks (other threads available upon request)…
    • Call To Place Order
  • BLOW BY METER Quick View
    • BLOW BY METER Quick View
    • ,
    • BLOW BY METER

    • $175.00
    • Engine builders and Dyno Operators have successfully used "Blow By" as a prime indicator of a ring seal efficiency. Properly used in conjunction with a leak-down meter, you can accurately monitor your engine's condition. Tool can be mounted on Dyno or in the car Perfect for evaluating evacuation pumps on race cars Meters are 16" long with mounting hardware included…
    • Order Online