• 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • ,
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor

    • $375.00
    • *Allows for one pass cuts on cylinder heads. *Choice of an  R-8 Adaptor for use with a Bridgegport-type Mill or a 1" Stub Arbor to be held in an end mill holder. *The flycutter NOW comes with a REPLACEABLE  Carbide Insert Tool Holder.  One insert for Cast Iron and one insert for Aluminum heads are included.  Additional inserts (specify cast…
    • Order Online
  • A B EPOXY Quick View
    • A B EPOXY Quick View
    • ,
    • A B EPOXY

    • $30.00
    • This is the good stuff. Works great on intake runners and manifolds. Molds like clay and maintains the formed shape without sagging or running. Stays where you put it ~ gas or alcohol doesn’t hurt it. Sets up harder than Superman’s Head in about 3 hours, yet machines very well. Forget the exhaust ports ~ it lasted 3 pulls on…
    • Call To Order
  • BEARING DRIVER Quick View
    • BEARING DRIVER Quick View
    • ,
    • BEARING DRIVER

    • $50.00
    • This fixture enables you to install the pinion support bearing on a 9" Ford without killing the race. Made of ALUMINUM Steel driving ring Anodized for appearance and durability Enhances the installation of a ring and pinion Give Us A Call To Order Now.
    • Order Online
  • BLOCK & HEAD HANDLES Quick View
    • BLOCK & HEAD HANDLES Quick View
    • ,
    • BLOCK & HEAD HANDLES

    • $45.00
    • These simple little tools take a lot of work out of handling and transporting heads, blocks or entire engine assemblies. Simply thread into any 3/8” 16 tpi bolt hole and you have an instant handle. NOTE: Be sure to screw handles in flush with block/head to prevent bending screws.   Set includes: 4 aluminum handles Heat-treated ~ 8 3/8” 16…
    • Call To Place Order
  • BLOCK DECK HEIGHT GAUGE Quick View
    • BLOCK DECK HEIGHT GAUGE Quick View
    • ,
    • BLOCK DECK HEIGHT GAUGE

    • $200.00
    • This is what you use to assure all four corners of your block are the same distance from the crankshaft. Remember, all the work on center to center rod length, piston compression height, and correcting the crank stroke, are out the window if your block isn't square. The tool can also be used for actual measurement if set with a…
    • Order Online
  • Carbide Insert Tool Holder for 8″ FlycutterCarbide Insert Tool Holder for 8″ Flycutter Quick View
    • Carbide Insert Tool Holder for 8″ FlycutterCarbide Insert Tool Holder for 8″ Flycutter Quick View
    • Carbide Insert Tool Holder for 8″ Flycutter

    • $80.00
    • CARBIDE INSERT TOOL HOLDER for 8" PMS FLYCUTTER New insert-type tool holder with inserts for cast iron and aluminum included (one each). Anyone that has previously purchased one of our 8" PMS Flycutters ~ this will directly replace the present cutter and greatly enhance the flycutter's performance.  You will really like it!    
    • Order Online
  • Cartridge Rolls, Mandrels & Flap Wheels Quick View
    • Cartridge Rolls, Mandrels & Flap Wheels Quick View
    • ,
    • Cartridge Rolls, Mandrels & Flap Wheels

    • Perfect for Finishing or Clean Up * Aluminum Oxide (Resin Bond) * 24 ~ 40 ~ 60 ~ 80 ~ 120 Grits * Extra-long Mandrels * 3/8 x 1 ½ inch or 5/8 x 1 ½ inch in Stock *2” Flap-Wheels in 60 or 120 Grit   $55  Cartridge Rolls 3/8" ~ Grit:  40/60/80/120 (Box of 100) $70  Cartridge Rolls…
    • Call To Order
  • Deburring Tool Quick View
  • Dial Indicator ExtensionsDial Indicator Extensions Quick View
  • Digital Inclinometer – Smart Level Quick View
    • Digital Inclinometer – Smart Level Quick View
    • ,
    • Digital Inclinometer – Smart Level

    • $125.00
    • This is an amazing tool for the price. Perfect for machine shops or chassis builders. Works great for leveling heads and blocks for surfacing, setting drive shaft and pinion angles, setting wing angles or checking caster and camber angles. The tool will repeat within .1 degree (one tenth of one degree) accuracy. It will also zero at any angle and…
    • Call To Place Order
  • Edge Finder Quick View
    • Edge Finder Quick View
    • ,
    • Edge Finder

    • $40.00
    • for Bridgeport-Type Mill This is sort of a gimmick.....but it works like a charm ~ within .0001 of contact . A “clicking” no ise is emitted when the edge is found. It really allows you to use both your eyes & ears for location. Repeats every time! Within .0001 accuracy!
    • Call To Place Order
  • Engine Turning ToolEngine Turning Tool Quick View
    • Engine Turning ToolEngine Turning Tool Quick View
    • ,
    • Engine Turning Tool

    • $40.00
    • After building a few engines, you come up with little goodies like this engine turning tool that make the job a lot easier. If you read the handle of a new “Snap On” screwdriver, it states “Warning: NOT a Pry Bar or Punch.” This tool also eliminates the search for a longer bolt because you just stripped the first1 ½”of…
    • Call To Place Order