• 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • ,
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor

    • $325.00
    • *Allows for one pass cuts on cylinder heads. *Choice of an  R-8 Adaptor for use with a Bridgegport-type Mill or a 1" Stub Arbor to be held in an end mill holder. *The flycutter NOW comes with a REPLACEABLE  Carbide Insert Tool Holder.  One insert for Cast Iron and one insert for Aluminum heads are included.  Additional inserts (specify cast…
    • Order Online
  • A B EPOXY Quick View
    • A B EPOXY Quick View
    • ,
    • A B EPOXY

    • $30.00
    • This is the good stuff. Works great on intake runners and manifolds. Molds like clay and maintains the formed shape without sagging or running. Stays where you put it ~ gas or alcohol doesn’t hurt it. Sets up harder than Superman’s Head in about 3 hours, yet machines very well. Forget the exhaust ports ~ it lasted 3 pulls on…
    • Call To Order
  • BEARING DRIVER Quick View
    • BEARING DRIVER Quick View
    • ,
    • BEARING DRIVER

    • $50.00
    • This fixture enables you to install the pinion support bearing on a 9" Ford without killing the race. Made of ALUMINUM Steel driving ring Anodized for appearance and durability Enhances the installation of a ring and pinion Give Us A Call To Order Now.
    • Order Online
  • BLOCK & HEAD HANDLES Quick View
    • BLOCK & HEAD HANDLES Quick View
    • ,
    • BLOCK & HEAD HANDLES

    • $45.00
    • These simple little tools take a lot of work out of handling and transporting heads, blocks or entire engine assemblies. Simply thread into any 3/8” 16 tpi bolt hole and you have an instant handle. NOTE: Be sure to screw handles in flush with block/head to prevent bending screws.   Set includes: 4 aluminum handles Heat-treated ~ 8 3/8” 16…
    • Call To Place Order
  • BLOCK DECK HEIGHT GAUGE Quick View
    • BLOCK DECK HEIGHT GAUGE Quick View
    • ,
    • BLOCK DECK HEIGHT GAUGE

    • $200.00
    • This is what you use to assure all four corners of your block are the same distance from the crankshaft. Remember, all the work on center to center rod length, piston compression height, and correcting the crank stroke, are out the window if your block isn't square. The tool can also be used for actual measurement if set with a…
    • Order Online
  • Carbide Insert Tool Holder for 8″ FlycutterCarbide Insert Tool Holder for 8″ Flycutter Quick View
    • Carbide Insert Tool Holder for 8″ FlycutterCarbide Insert Tool Holder for 8″ Flycutter Quick View
    • Carbide Insert Tool Holder for 8″ Flycutter

    • $80.00
    • CARBIDE INSERT TOOL HOLDER for 8" PMS FLYCUTTER New insert-type tool holder with inserts for cast iron and aluminum included (one each). Anyone that has previously purchased one of our 8" PMS Flycutters ~ this will directly replace the present cutter and greatly enhance the flycutter's performance.  You will really like it!    
    • Order Online
  • Cartridge Rolls, Mandrels & Flap Wheels Quick View
    • Cartridge Rolls, Mandrels & Flap Wheels Quick View
    • ,
    • Cartridge Rolls, Mandrels & Flap Wheels

    • Perfect for Finishing or Clean Up * Aluminum Oxide (Resin Bond) * 24 ~ 40 ~ 60 ~ 80 ~ 120 Grits * Extra-long Mandrels * 3/8 x 1 ½ inch or 5/8 x 1 ½ inch in Stock *2” Flap-Wheels in 60 or 120 Grit   $55  Cartridge Rolls 3/8" ~ Grit:  40/60/80/120 (Box of 100) $70  Cartridge Rolls…
    • Call To Order
  • Deburring Tool Quick View
  • Dial Indicator ExtensionsDial Indicator Extensions Quick View
  • Digital Inclinometer – Smart Level Quick View
    • Digital Inclinometer – Smart Level Quick View
    • ,
    • Digital Inclinometer – Smart Level

    • $125.00
    • This is an amazing tool for the price. Perfect for machine shops or chassis builders. Works great for leveling heads and blocks for surfacing, setting drive shaft and pinion angles, setting wing angles or checking caster and camber angles. The tool will repeat within .1 degree (one tenth of one degree) accuracy. It will also zero at any angle and…
    • Call To Place Order
  • Edge Finder Quick View
    • Edge Finder Quick View
    • ,
    • Edge Finder

    • $40.00
    • for Bridgeport-Type Mill This is sort of a gimmick.....but it works like a charm ~ within .0001 of contact . A “clicking” no ise is emitted when the edge is found. It really allows you to use both your eyes & ears for location. Repeats every time! Within .0001 accuracy!
    • Call To Place Order
  • Engine Turning ToolEngine Turning Tool Quick View
    • Engine Turning ToolEngine Turning Tool Quick View
    • ,
    • Engine Turning Tool

    • $40.00
    • After building a few engines, you come up with little goodies like this engine turning tool that make the job a lot easier. If you read the handle of a new “Snap On” screwdriver, it states “Warning: NOT a Pry Bar or Punch.” This tool also eliminates the search for a longer bolt because you just stripped the first1 ½”of…
    • Call To Place Order
  • Fiber Stones for Aluminum Quick View
    • Fiber Stones for Aluminum Quick View
    • ,
    • Fiber Stones for Aluminum

    • $8.00
    • This is a new fiber-bond mounted wheel developed by Norton Abrasives. It was designed to clean up aluminum castings in foundries. It is not a rotary file for porting, but does a real good job of replacing sanding rolls for cleaning up and smoothing ports and manifolds. Use with WD-40 Stones are available in ½” & 5/8” diameter 1” long…
    • Call To Order
  • Flow Bench Valve Opening Fixture Quick View
    • Flow Bench Valve Opening Fixture Quick View
    • ,
    • Flow Bench Valve Opening Fixture

    • $175.00
    • Finally a truly universal fixture for your flow bench. Now you need only one valve opening fixture for ALL heads! *Rigid design ~ will not flex, bend or slip *Easily control opening height to .001” *Plenty of travel for the biggest cams *Works on canted or straight valve applications *Complete with specially modified dial indicator, 3/8” & 7/16” stud adaptors…
    • Call To Place Order
  • Flycutter Scribe Quick View
    • Flycutter Scribe Quick View
    • ,
    • Flycutter Scribe

    • $35.00
    • This handy little unit is a helpful accessory to your piston vise and flycutting tools. The valve diameter and clearance can be preset with a ruler or calipers and transferred to the piston dome by chucking the scribe in the mill and bluing the top of the piston to be cut. The diameter can be located correctly on the piston…
    • Call To Place Order
  • FLYCUTTER SET Quick View
    • FLYCUTTER SET Quick View
    • ,
    • FLYCUTTER SET

    • $50.00
    • This fixture is a big help when it comes to torquing the pinion nut on a 9” Ford (works on others as well).   Eliminates the need for pipe wrenches, etc. and saves a lot of skinned knuckles. Made of aluminum and anodized for appearance and durability.
    • Call To Place Order
  • Four-In-One Head ToolFour-In-One Head Tool Quick View
    • Four-In-One Head ToolFour-In-One Head Tool Quick View
    • ,
    • Four-In-One Head Tool

    • $200.00
    • This tool is the head work's "Best Friend" The four-in-one tool is a must if you are doing complete valve jobs, touching up seats, or just checking another shop’s work. CONCENTRICITY: Quickly & accurately measure valve seat “runout”. SEAT DEPTH: Valve seat depth consistency between cylinders is an absolute must to compression ratio & piston to valve clearance This tool…
    • Call To Order
  • JAR OPENER Quick View
    • JAR OPENER Quick View
    • ,
    • JAR OPENER

    • $40.00
    • Effortlessly open any jar lid from 1/2" Tabasco Sauce jars to the large 4 1/2" gallon pickle jars NO CHEAP PLASTIC OR WOOD USED HERE! Manufactured totally in the USA by PMS from CNC billet aluminum -- stainless and high speed steel Clear ANODIZED for appearance and durability Easily mounts under any cabinet or shelf (mounting screws included) -- takes…
    • Order Online
  • MANUAL VALVE SPRING COMPRESSOR Quick View
  • OIL FILTER CUTTER Quick View
    • OIL FILTER CUTTER Quick View
    • ,
    • OIL FILTER CUTTER

    • $60.00
    • This is a good one! There are a ton of these on the market, and most are junk. The three-point nesting allows for very smooth cutting ~ as opposed to the tools with a plug that locates off the center of the filter. This unit will work on virtually ANY filter
    • Call To Place Order
  • Oil Pump Pick Up Tube Installer Quick View
    • Oil Pump Pick Up Tube Installer Quick View
    • ,
    • Oil Pump Pick Up Tube Installer

    • $50.00
    • Allows easy installation of pickup tube in the pump. A job that can sometimes turn into a frustrating endeavor. The tool is machined from carbon steel and heattreated for long life. There is a brass insert in the end of the tool which prevents tearing it up on the hammered surface. Fits Big Block & Small Block Chevrolet
    • Call To Place Order
  • Optical Center Punch Quick View
    • Optical Center Punch Quick View
    • ,
    • Optical Center Punch

    • $90.00
    • This is one of the handiest layout tools you can have in your tool box. You can center punch scribed lines with unbelievable accuracy. * Simply place cone over your scribed lines * Insert magnifier & align scribed lines with the cross lines on the bottom of the magnifier. * Hold cone in position, remove the magnifier and insert center…
    • Call To Order
  • PICK SET Quick View
    • PICK SET Quick View
    • ,
    • PICK SET

    • $30.00
    • All of us have enjoyed the task of removing Spiral Loks from the pistons. This little kit will take a lot of work out of this frustrating chore. You will find hundreds of uses for this pick set.   Made in the USA Heat-treated tool steel w/ an aluminum handle and handy magnet inserted in the handle end.   The…
    • Call To Place Order
  • PINION DEPTH SETTING TOOLPINION DEPTH SETTING TOOL Quick View
    • PINION DEPTH SETTING TOOLPINION DEPTH SETTING TOOL Quick View
    • ,
    • PINION DEPTH SETTING TOOL

    • $150.00
    • After many hours of development and testing, we have finally devised a truly universal pinion setting fixture without the use of spools, bars, etc.  This tool is quick to set up and is ACCURATE. Works on GM - 10 & 12 bolts.  Early GM, Ford 9", 8.8" and 7.5", Chrysler 8 3/4", Dana and many others. Mounting distances are provided…
    • Order Online
  • Port Radiusing Mandrel & PSA Discs Quick View
    • Port Radiusing Mandrel & PSA Discs Quick View
    • ,
    • Port Radiusing Mandrel & PSA Discs

    • $45.00
    • $25  Port Radiusing Mandrel $20  PSA Discs  Available Grits:  40/60/80/120  (Box of 100) Port Radiusing Mandrel & PSA Discs This is a unique little mandrel we came up with for polishing ports & mandrels. It is used by placing PSA discs (sold separately) back-to-back on the arbor with spacers in between them so you have a two-sided cutting disc. This…
    • Call To Place Order
  • Self Aligning Tapper Quick View
    • Self Aligning Tapper Quick View
    • ,
    • Self Aligning Tapper

    • $60.00
    • As most of you know, it is very difficult to start a tap straight. This little tool will save a lot of frustration and ruined parts. It automatically squares and trues up the tap with the hole which will stop a lot of tool breakage. The base is also milled with a 120 degree “V” for round work. Complete with…
    • Call To Place Order
  • Spanner Wrench ~ SIDE BEARING ADJUSTOR WRENCH Quick View
  • SPRING LOADED LAYOUT SCRIBESPRING LOADED LAYOUT SCRIBE Quick View
    • SPRING LOADED LAYOUT SCRIBESPRING LOADED LAYOUT SCRIBE Quick View
    • ,
    • SPRING LOADED LAYOUT SCRIBE

    • $40.00
    • This is one of the neatest tools you can have in your tool box for layout work! Here is how it works: * Spray your work with Dykum Blue * Place in scribe in the chuck * Pre-load scribe * Turn on your digital readout PRESTO! You can layout any bolt pattern or fixture with amazing accuracy & it is…
    • Call To Place Order
  • TELESCOPING SPARK PLUG SOCKETTELESCOPING SPARK PLUG SOCKET Quick View
    • TELESCOPING SPARK PLUG SOCKETTELESCOPING SPARK PLUG SOCKET Quick View
    • ,
    • TELESCOPING SPARK PLUG SOCKET

    • $20.00
    • If you own a hot rod with headers, you will appreciate this little jewel. Very thin wall machining allows access into the tightest places. Socket fits both 5/8" and 13/16" plugs. Retracted form is only .750" long -- telescopes out to 1.750". This heat-treated tool is cadmium plated and carries a lifetime warranty against breakage. This truly is one of…
    • Order Online
  • Transfer Punch Set Quick View
    • Transfer Punch Set Quick View
    • ,
    • Transfer Punch Set

    • $45.00
    • If you’ve never owned a set of transfer punches, you’ve been doing a lot of unnecessary work! * Set includes 28 punches 3/32” to1/2” by 64th * Supplied with index stand with all sizes marked for fast and easy use * Supplied in fitted carton box
    • Call To Place Order
  • Universal “Chopsticks” Quick View
    • Universal “Chopsticks” Quick View
    • ,
    • Universal “Chopsticks”

    • $50.00
    • *Interchangeable inserts accept all common size rod bolts (one size fits all): 5/16”, 3/8”, 11/32”, & 7/16” *Extended length allows operator to “GUIDE” assembly into place *Eliminates nicked or damaged cranks *Speeds up assembly and makes short block assembly a lot easier *Color coded inserts for easy identification *1/2” anodized aluminum ~ 7” overall length
    • Call To Place Order
  • Universal Pointer Quick View
  • Valve Opening Comparator & Transfer Gauge Quick View
    • Valve Opening Comparator & Transfer Gauge Quick View
    • ,
    • Valve Opening Comparator & Transfer Gauge

    • $35.00
    • This is a straightforward tool that performs a VERY VITAL job in flycutting pistons. It is very critical that the valve relief in the piston is the same angle as the valve in the head ~ especially on high RPM applications where piston-to-valve clearance is at a minimum. Usually, if you float the valves and they hit the piston squarely,…
    • Call To Place Order
  • Wire Bender Quick View
    • Wire Bender Quick View
    • ,
    • Wire Bender

    • $100.00
    • Secure bender to workbench or clamp in a vise. Lay up to 1/4” O.D. Wire between the two pins in the base and slide handle over the 3/8” pin. Insert the 5/16” pin (with plastic cap) into handle and to the side of the wire to be bent. Make bend by pulling handle toward you. Placement of the 5/16” dowel…
    • Call To Place Order
  • YOKE SUPPORT FOR PINION NUTYOKE SUPPORT FOR PINION NUT Quick View