• 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor Quick View
    • ,
    • 8″ FLYCUTTER with Stub Arbor or R-8 Adaptor

    • $375.00
    • *Allows for one pass cuts on cylinder heads. *Choice of an  R-8 Adaptor for use with a Bridgegport-type Mill or a 1" Stub Arbor to be held in an end mill holder. *The flycutter NOW comes with a REPLACEABLE  Carbide Insert Tool Holder.  One insert for Cast Iron and one insert for Aluminum heads are included.  Additional inserts (specify cast…
    • Order Online
  • BEARING DRIVER Quick View
    • BEARING DRIVER Quick View
    • ,
    • BEARING DRIVER

    • $50.00
    • This fixture enables you to install the pinion support bearing on a 9" Ford without killing the race. Made of ALUMINUM Steel driving ring Anodized for appearance and durability Enhances the installation of a ring and pinion Give Us A Call To Order Now.
    • Order Online
  • Bellhousing Indexing FixtureBellhousing Indexing Fixture Quick View
    • Bellhousing Indexing FixtureBellhousing Indexing Fixture Quick View
    • ,
    • Bellhousing Indexing Fixture

    • $75.00
    •   This is the tool that is often over-looked when installing a manual transmission.  It is also the tool that is responsible for a clean releasing clutch and smooth shifting.   Believe me, not ONE scattershield made is concentric with the crankshaft as they come from the factory.  All of them must be indicated and adjusted for proper alignment and…
    • Purchase on Ebay store
  • BLOCK DECK HEIGHT GAUGE Quick View
    • BLOCK DECK HEIGHT GAUGE Quick View
    • ,
    • BLOCK DECK HEIGHT GAUGE

    • $200.00
    • This is what you use to assure all four corners of your block are the same distance from the crankshaft. Remember, all the work on center to center rod length, piston compression height, and correcting the crank stroke, are out the window if your block isn't square. The tool can also be used for actual measurement if set with a…
    • Order Online
  • BLOW BY METER Quick View
    • BLOW BY METER Quick View
    • ,
    • BLOW BY METER

    • $175.00
    • Engine builders and Dyno Operators have successfully used "Blow By" as a prime indicator of a ring seal efficiency. Properly used in conjunction with a leak-down meter, you can accurately monitor your engine's condition. Tool can be mounted on Dyno or in the car Perfect for evaluating evacuation pumps on race cars Meters are 16" long with mounting hardware included…
    • Order Online
  • CARBURETOR JET ORGANIZERS Quick View
    • CARBURETOR JET ORGANIZERS Quick View
    • ,
    • CARBURETOR JET ORGANIZERS

    • $20.00
    • Tired of searching through the tool box for a set of jets you saw "just the other day"?   Eliminate this common problem with these handy jet organizers.   Available for Holley, Rochester or Carter  (PLEASE SPECIFY WHEN YOU PURCHASE) Each Organizer Bar Holds 32 Jets Slim/Trim Design Allows Easy Carrying & Storage Attach Several Together with a Key Chain…
    • Order Online
  • CHAMFERING TOOL ~ ROD OR MAIN BEARING Quick View
    • CHAMFERING TOOL ~ ROD OR MAIN BEARING Quick View
    • ,
    • CHAMFERING TOOL ~ ROD OR MAIN BEARING

    • $85.00
    • If you have to use a breaker bar instead of a ratchet to turn your short block over, you might check this tool out (among other things).   Race cranks have a big fillet to reduce stress risers of sharp corners.  Bearings are not made for this large radius, and many times must be chamfered for clearance.  This tool is…
    • Order Online
  • CRANKSHAFT V-BLOCKSCRANKSHAFT V-BLOCKS Quick View
    • CRANKSHAFT V-BLOCKSCRANKSHAFT V-BLOCKS Quick View
    • ,
    • CRANKSHAFT V-BLOCKS

    • $200.00
    • Finally, a quick and accurate fixture for postioning a crankshaft on a mill table! FEATURES: *Universal Application ~ Will Hold Any Crankshaft *Keyed Base Assures Perfect Alignment *Ideal for: Cross Drilling ~ Milling Key-Ways ~Checking Stroke Consistency & Many Other Milling & Drilling Operations *Includes:  Keys, Caps & Bolts *CNC Machined from Billet Aluminum *Anodized for Appearance & Durability
    • Order Online
  • CYLINDER HEAD FIXTURE w/ FLYCUTTER & STUB ARBOR OR R-8CYLINDER HEAD FIXTURE w/ FLYCUTTER & STUB ARBOR OR R-8 Quick View
    • CYLINDER HEAD FIXTURE w/ FLYCUTTER & STUB ARBOR OR R-8CYLINDER HEAD FIXTURE w/ FLYCUTTER & STUB ARBOR OR R-8 Quick View
    • ,
    • CYLINDER HEAD FIXTURE w/ FLYCUTTER & STUB ARBOR OR R-8

    • $925.00
    • $650 Cylinder Head Fixture Only (call to order) This Fixture Really Adds Versatility to Your Vertical Milling Machine Provides operator with quick, rigid setups on what used to be impossible or cumbersome items. *Great for Holding Intake Manifolds *The flycutter NOW comes with a REPLACEABLE Carbide Insert Tool Holder.  One insert for Cast Iron and one insert for Aluminum heads are…
    • Order Online
  • Effective Uses of the Bridgeport Type Mill Quick View
    • Effective Uses of the Bridgeport Type Mill Quick View
    • ,
    • Effective Uses of the Bridgeport Type Mill

    • $79.00
    • This 3-Part Video Series is loaded with tips on how to get the most from your vertical mill. Presented by Adrian Pendergrass with over 20 years of experience of "hanging on the end of a lathe and a mill". Perfect for home, shop or vocational use. Designed to increase your confidence and make you want to use your mill.
    • Order Online
  • ENGINE BALANCING FIXTURE Quick View
    • ENGINE BALANCING FIXTURE Quick View
    • ,
    • ENGINE BALANCING FIXTURE

    • $300.00
    • Any machine shop will agree that the time consuming part of balancing an engine is weighing and equalizing the rods and pistons.  Spinning the crank and adding Mallory or drilling to remove weight is the easy part.  The PMS Balancing Fixture allows you to do all of the time consuming (expensive) work yourself.  You can now take your crank, harmonic…
    • Order Online
  • GAS PORT DRILLING FIXTUREGAS PORT DRILLING FIXTURE Quick View
    • GAS PORT DRILLING FIXTUREGAS PORT DRILLING FIXTURE Quick View
    • ,
    • GAS PORT DRILLING FIXTURE

    • $250.00
    • * This fixture is designed to allow racers & engine builders to drill gas port holes using a drill press or vertical mill * Anodized Aluminum Construction * Accepts .043 or 1/26" Ring Groove * Two .040 (No. 60) Drill Bits * One Specially Ground Center Drill Included Complete Instruction Sheet with Pictures & Helpful Hints $5  Extra Center Drills…
    • Order Online
  • JAR OPENER Quick View
    • JAR OPENER Quick View
    • ,
    • JAR OPENER

    • $40.00
    • Effortlessly open any jar lid from 1/2" Tabasco Sauce jars to the large 4 1/2" gallon pickle jars NO CHEAP PLASTIC OR WOOD USED HERE! Manufactured totally in the USA by PMS from CNC billet aluminum -- stainless and high speed steel Clear ANODIZED for appearance and durability Easily mounts under any cabinet or shelf (mounting screws included) -- takes…
    • Order Online
  • Lathe Learnin’ 5-Part Instructional Video Series Quick View
    • Lathe Learnin’ 5-Part Instructional Video Series Quick View
    • ,
    • Lathe Learnin’ 5-Part Instructional Video Series

    • $125.00
    • Presented by Adrian Pendergrass with over 20 years of experience of “hanging on the end” of a lathe and a mill. Material is not only interesting and correct, but presented in an easy to follow and entertaining manner. Something for experienced operators as well as the novice. Highly recommended for home, shop and Vo-Tech institutions. Series covers many operations, valuable…
    • Order Online
  • LEAK DOWN METER ~ DIFFERENTIAL PRESSURE CYLINDER TESTER Quick View
  • MAGNETIC DECK BRIDGEMAGNETIC DECK BRIDGE Quick View
    • MAGNETIC DECK BRIDGEMAGNETIC DECK BRIDGE Quick View
    • ,
    • MAGNETIC DECK BRIDGE

    • $75.00
    • You will find many uses for this Bridge!  Besides checking deck to piston clearance, it's perfect for accurately for locating top dead center, checking cam and crank end play -- and many other applications!   FEATURES: *Magnetic Base Secures Fixture to Block & Frees Operator's Hands *Three Holes Drilled & Tapped for Collet Locations *4  3/16" Inside Span Covers Virtually…
    • Purchase on Ebay store
  • Mini Valve Spring Tester Quick View
  • PINION DEPTH SETTING TOOLPINION DEPTH SETTING TOOL Quick View
    • PINION DEPTH SETTING TOOLPINION DEPTH SETTING TOOL Quick View
    • ,
    • PINION DEPTH SETTING TOOL

    • $150.00
    • After many hours of development and testing, we have finally devised a truly universal pinion setting fixture without the use of spools, bars, etc.  This tool is quick to set up and is ACCURATE. Works on GM - 10 & 12 bolts.  Early GM, Ford 9", 8.8" and 7.5", Chrysler 8 3/4", Dana and many others. Mounting distances are provided…
    • Order Online
  • Pinion Depth Setting Tool Instructional video ~ DVD Quick View
    • Pinion Depth Setting Tool Instructional video ~ DVD Quick View
    • ,
    • Pinion Depth Setting Tool Instructional video ~ DVD

    • $40.00
    • This is a step-by-step instructional video covering the set up and use of the Pinion Depth Setting Tool, along with difficult to obtain rearend buildup procedure and information. Gear nomenclature Gearset applications Patterns Helpful Hints Torque Specifications ENHANCES INSTALLATION OF A RING AND PINION PINION DEPTH SETTING TOOL SOLD SEPARATELY
    • Order Online
  • PUSHROD LENGTH CHECKER Quick View
    • PUSHROD LENGTH CHECKER Quick View
    • ,
    • PUSHROD LENGTH CHECKER

    • $150.00
    • Correct pushrod length is a vital part of rocker arm geometry, and is also one of the most overlooked steps in engine building.  Poor rocket geometry is probably the major cause in valve train failure.  Until now, no one has made a tool for checking pushrod length ~ it is a difficult job with calipers, etc. Well, no more excuses! …
    • Purchase on Ebay store
  • Ring Spacer Gas Porting Fixture Quick View
    • Ring Spacer Gas Porting Fixture Quick View
    • ,
    • Ring Spacer Gas Porting Fixture

    • $200.00
    • Perfect for Stock Eliminator & Crate Motor Classes Where Modifying Pistons (Gas Porting) Is Not Allowed Absolute Power Gain Technique Used By Most Top Stock Eliminator Engine Builders Fixture Makes It Easy and Accurate With the Use of Any Mill 6061 Anodized Aluminum ~ CNC Machined Fixture is Keyed & Drilled & Counterbored For Accurate Alignment ~ Two 5/8" Keys…
    • Order Online
  • ROD BOLT STRETCH GAUGEROD BOLT STRETCH GAUGE Quick View
    • ROD BOLT STRETCH GAUGEROD BOLT STRETCH GAUGE Quick View
    • ,
    • ROD BOLT STRETCH GAUGE

    • $150.00
    • There is a very good reason why quality bolt manufacturers for both aircraft and automotive fields use bolt stretch as opposed to torque figures for fastener assembly.  Torque readings are affected by bolt condition, nut condition, material used, lubricant, bearing surface, accuracy of wrench, type of socket, etc.  All of these are variables and do influence proper assembly.  PMS will…
    • Purchase on Ebay store
  • Rod ViseRod Vise Quick View
    • Rod ViseRod Vise Quick View
    • ,
    • Rod Vise

    • $175.00
    • An Absolute Must for Resizing or Installing New Rod Bolts Anodized Aluminum & Steel Construction Eliminates Bent or Twisted Rods or Caps Aluminum Jaws Will Not Mar Finish, Yet Hold Rod Securely Unique Base Design Allows Clamping in Bench Vise OR May be Permanently Mounted Holds Rod for Beam Polishing or Grinding
    • Order Online
  • Safety Wire Drilling Fixture Quick View
    • Safety Wire Drilling Fixture Quick View
    • ,
    • Safety Wire Drilling Fixture

    • $75.00
    • No More Excuses! Now you can easily drill any bolt for safety wiring. *Accepts Bolts from .198" to .562" in Diameter *Works on All Hex Head or Socket Head Bolts *Design of Fixture Actually Clamps Bolt to Ensure Straight Holes and Prevent Drill Breakage *Fixture is Complete with Two Bushings and Two .062" Drill Bits *Anodized Aluminum Construction for Appearance…
    • Order Online