This is the good stuff. Works great on intake runners and manifolds. Molds like clay and maintains the formed shape without sagging or running. Stays where you put it ~ gas or alcohol doesn’t hurt it. Sets up harder than Superman’s Head in about 3 hours, yet machines very well. Forget the exhaust ports ~ it lasted 3 pulls on…
*Fits both cup & ball type rocker arms *Eliminates trial and error fittings ~a must for making correct length pushrods *Simply adjust pushrod length to yield desired rocker arm geometry, measure sample and cut length correctly the first time
This is one of the handiest tools you’ll use around your mill or drill press. Simply insert tool into chuck and move table in or out until both dowels contact shaft simultaneously, and you are exactly centered over the workpiece. Fast, accurate and illustrated in our “Bridgeport Mill Video”.
This is what you use to mike bearings. It is common knowledge that all bearings are not the same thickness. By juggling bearing thickness, a lot of clearance problems can be eliminated. * .0001 Graduation * Carbide Faces (Anvil & Spindle) * Wrench Included for Quick Zero Adjustment
* In stock for popular chucks * Bolt jaws on in place of permanent jaws * Machine in place for perfect accuracy and concentricity * A must for holding pistons while cutting ring grooves or facing flat tops * Spiders also available * Complete instructions Specify exact chuck specs including: Make, Model No. & Size
These simple little tools take a lot of work out of handling and transporting heads, blocks or entire engine assemblies. Simply thread into any 3/8” 16 tpi bolt hole and you have an instant handle. NOTE: Be sure to screw handles in flush with block/head to prevent bending screws. Set includes: 4 aluminum handles Heat-treated ~ 8 3/8” 16…
This fixture is perfect for degreeing a camshaft because when the unit is screwed into the deck surface, the stem of the indicator is always parallel to the lifter bores. * Tool is machined & black anodized * Complete with 5” extension for reaching down to filter *1/2” & 7/16” threaded shaft fits most blocks (other threads available upon request)…
Perfect for Finishing or Clean Up * Aluminum Oxide (Resin Bond) * 24 ~ 40 ~ 60 ~ 80 ~ 120 Grits * Extra-long Mandrels * 3/8 x 1 ½ inch or 5/8 x 1 ½ inch in Stock *2” Flap-Wheels in 60 or 120 Grit $55 Cartridge Rolls 3/8" ~ Grit: 40/60/80/120 (Box of 100) $70 Cartridge Rolls…
This fixture allows the operator to quickly and accurately measure rods for precise center to center distances ~ or compare rods before and after resizing. * Takes a lot of work out of setting deck height * Reveals how much material to grind from the cap or rod to even out center length * Compare a number of rods to…
This is a copy of the P&G Gauge with a lot more capacity with the same accuracy. This tool is a must for any track or organization running events with a cubic inch limit rule. Eliminate pulling heads and still keep them honest. Tester is accurate within ½ C.I. Per cylinder (total of 4 cubic inches for a V-8). A…
You will find yourself carrying this tool around like a pocket knife. How many times have you been caught trying to figure out if a block is standard ~ .030 or .060 over and all you have is a tape measure? SPECIAL FEATURES: * Carbide-faced measuring tips are spherical to make positive point contact against the cylinder walls. * Graduations…
* Checks block for “CORE SHIFT” or dangerously thin cylinder walls before spending time & money on an inferior block * Fits cylinder bolt holes or water jacket holes * Tool is fast & accurate to .001” * Easily does the job of an ultrasonic tester at a fraction of the cost
Dial calipers are probably the most versatile measuring tool available. Provides inside, outside, as well as depth measurements up to six inches. FEATURES INCLUDE: *1.6” jaw depth *Stainless steel hardened throughout with measuring faces precision ground and lapped for ultimate accuracy. *Scale surface: Satin chrome finished with micro-fine engraved graduations in inches. *Accuracy .001” per 6” *Easily used, accurate-read…
This is an amazing tool for the price. Perfect for machine shops or chassis builders. Works great for leveling heads and blocks for surfacing, setting drive shaft and pinion angles, setting wing angles or checking caster and camber angles. The tool will repeat within .1 degree (one tenth of one degree) accuracy. It will also zero at any angle and…
for Bridgeport-Type Mill This is sort of a gimmick.....but it works like a charm ~ within .0001 of contact . A “clicking” no ise is emitted when the edge is found. It really allows you to use both your eyes & ears for location. Repeats every time! Within .0001 accuracy!
After building a few engines, you come up with little goodies like this engine turning tool that make the job a lot easier. If you read the handle of a new “Snap On” screwdriver, it states “Warning: NOT a Pry Bar or Punch.” This tool also eliminates the search for a longer bolt because you just stripped the first1 ½”of…
This is a new fiber-bond mounted wheel developed by Norton Abrasives. It was designed to clean up aluminum castings in foundries. It is not a rotary file for porting, but does a real good job of replacing sanding rolls for cleaning up and smoothing ports and manifolds. Use with WD-40 Stones are available in ½” & 5/8” diameter 1” long…
Finally a truly universal fixture for your flow bench. Now you need only one valve opening fixture for ALL heads! *Rigid design ~ will not flex, bend or slip *Easily control opening height to .001” *Plenty of travel for the biggest cams *Works on canted or straight valve applications *Complete with specially modified dial indicator, 3/8” & 7/16” stud adaptors…
This handy little unit is a helpful accessory to your piston vise and flycutting tools. The valve diameter and clearance can be preset with a ruler or calipers and transferred to the piston dome by chucking the scribe in the mill and bluing the top of the piston to be cut. The diameter can be located correctly on the piston…
This fixture is a big help when it comes to torquing the pinion nut on a 9” Ford (works on others as well). Eliminates the need for pipe wrenches, etc. and saves a lot of skinned knuckles. Made of aluminum and anodized for appearance and durability.
This fixture is a must for flycutting pistons! *Allows you to quickly & accurately preset flycutter to desired diameter *Eliminates trial and error settings *Range: .750” to 2.500” *Complete instructions Designed to work with PMS Flycutters
This tool is the head work's "Best Friend" The four-in-one tool is a must if you are doing complete valve jobs, touching up seats, or just checking another shop’s work. CONCENTRICITY: Quickly & accurately measure valve seat “runout”. SEAT DEPTH: Valve seat depth consistency between cylinders is an absolute must to compression ratio & piston to valve clearance This tool…
With the PMS kit, it is quick and simple to check the specific gravity of your gasoline for quality and legality. This kit is a real aid for the racer using additives or special blends. With the decreasing quality of today’s pump gas, a Gas Check Kit should be a standard item with all racers. * Easy to read lab-grade…
This is the ORIGINAL Stainless Steel ~ NOT Aluminum The Hite Mike installed height micrometer makes old valve springs installed height measuring methods obsolete. The Hite Mike installs on valve and retainer assembly as if it were a spring and reads installed height dimension direct. The expanding force of the tool simulates spring pressure for more accurate readings. It’s…
If you own a RIMAC Spring Tester, this fixture is a MUST. This adaptor allows the operator to check valve springs quickly with .001” accuracy. Eliminates the time and hassle of trying to read inaccurate scale or fumbling with preset snap gauges to measure spring height Guaranteed to repeat to .001” Adapter comes with 2” standard for fast, accurate…
Until now the only method of accurately measuring the actual orifice diameter has been plug gauges which is time consuming and very expensive. We have modified these calipers on a cutter grinder to gain access to the jet orifice and measure its diameter to .001 accuracy. Orifice diameter and jet numbers are not only the same, included is a…
* On/Off lever control for easy mounting & unmounting ~ no risk of scratching surfaces * Centered “V” magnet for strongest possible grip on round or flat surfaces * 125 lb. pull magnet * Rod may be mounted on top or side of base for greater versatility * Fine adjustment gives rigid, sensitive control of indicator on any plane ~…
This is the best on the market. Easily handles high performance springs of 700 plus lbs. * Compressor is the fastest manual available * Gusseted all steel construction * 2 5/8” plunger travel * Over-center clamp holds compressed spring with no effort
This is a good one! There are a ton of these on the market, and most are junk. The three-point nesting allows for very smooth cutting ~ as opposed to the tools with a plug that locates off the center of the filter. This unit will work on virtually ANY filter
Allows easy installation of pickup tube in the pump. A job that can sometimes turn into a frustrating endeavor. The tool is machined from carbon steel and heattreated for long life. There is a brass insert in the end of the tool which prevents tearing it up on the hammered surface. Fits Big Block & Small Block Chevrolet
This is one of the handiest layout tools you can have in your tool box. You can center punch scribed lines with unbelievable accuracy. * Simply place cone over your scribed lines * Insert magnifier & align scribed lines with the cross lines on the bottom of the magnifier. * Hold cone in position, remove the magnifier and insert center…
All of us have enjoyed the task of removing Spiral Loks from the pistons. This little kit will take a lot of work out of this frustrating chore. You will find hundreds of uses for this pick set. Made in the USA Heat-treated tool steel w/ an aluminum handle and handy magnet inserted in the handle end. The…
This tool is used in the lathe to cut pistons for “Tru Arcs” if you are changing from pressed to floated pins. Some customers have asked about bolting the tool to a piece of angle iron and using it as a piston vise in a mill ~ we sell a real piston vise. However, it does work well for holding…
This offers a quick and efficient means of properly filing ring end gaps. *Grinds the ring from the outside to the inside *Both sides of the gap are ground in one operation and are held parallel. *Replaceable carbide blade *Easily bolts to bench for hands-free operation $20 Piston Ring Filer Replacement Blades
Nothing on the market today compares with the quality of this vise. This is the best constructed, most rigid vise available for flycutting or milling pistons. CHECK OUT THESE FEATURES: Set up is off of the pin hole which insures that all pistons will be positioned the same. Superior engineering and workmanship assures excellent repeatability. Only the highest quality materials…
$25 Port Radiusing Mandrel $20 PSA Discs Available Grits: 40/60/80/120 (Box of 100) Port Radiusing Mandrel & PSA Discs This is a unique little mandrel we came up with for polishing ports & mandrels. It is used by placing PSA discs (sold separately) back-to-back on the arbor with spacers in between them so you have a two-sided cutting disc. This…
As most of you know, it is very difficult to start a tap straight. This little tool will save a lot of frustration and ruined parts. It automatically squares and trues up the tap with the hole which will stop a lot of tool breakage. The base is also milled with a 120 degree “V” for round work. Complete with…
.125" to .500" Range Ideal for measuring small holes up to ½”such as valve guides. Knurled knob at end of handle is used for size adjustment. Hole size is obtained by measuring over the contact points with an outside micrometer. Gauging surface is a full-round with a flat bottom; permits use in the smallest of shallow holes, slots and similar…
This is one of the neatest tools you can have in your tool box for layout work! Here is how it works: * Spray your work with Dykum Blue * Place in scribe in the chuck * Pre-load scribe * Turn on your digital readout PRESTO! You can layout any bolt pattern or fixture with amazing accuracy & it is…
Plungers of gauge expand from the center, under spring tension, to the size of the hole being measured, and is then locked in place by knurled knob. Final hole size is obtained by measuring over contacts with a micrometer or dial calipers. SPECIAL FEATURES INCLUDE: * Double Action (self-centering) for quick checking of inside bores * Rigid handle with…
If you’ve never owned a set of transfer punches, you’ve been doing a lot of unnecessary work! * Set includes 28 punches 3/32” to1/2” by 64th * Supplied with index stand with all sizes marked for fast and easy use * Supplied in fitted carton box
*Interchangeable inserts accept all common size rod bolts (one size fits all): 5/16”, 3/8”, 11/32”, & 7/16” *Extended length allows operator to “GUIDE” assembly into place *Eliminates nicked or damaged cranks *Speeds up assembly and makes short block assembly a lot easier *Color coded inserts for easy identification *1/2” anodized aluminum ~ 7” overall length
This handy tool allows you to gap your valves w/.001” accuracy. Feeler gauges take just that “a feel”. Ask three people to run valves with a feeler gauge and you will get three different results. * Anodized Aluminum *Complete with attachment rings for: 1.400”, 1.437”, 1.500”, 1.575” retainer (others available) * Starrett indicator for precise accuracy & wedge for milled…
This is a straightforward tool that performs a VERY VITAL job in flycutting pistons. It is very critical that the valve relief in the piston is the same angle as the valve in the head ~ especially on high RPM applications where piston-to-valve clearance is at a minimum. Usually, if you float the valves and they hit the piston squarely,…
I don’t care who does your head work. If they can’t seal the valves, something is very wrong and you need to catch the problem and correct it BEFORE engine assembly. Several companies make a vacuum tester, but we took the time to design a real nice unit that fits the needs of a race car. This unit was designed…
Secure bender to workbench or clamp in a vise. Lay up to 1/4” O.D. Wire between the two pins in the base and slide handle over the 3/8” pin. Insert the 5/16” pin (with plastic cap) into handle and to the side of the wire to be bent. Make bend by pulling handle toward you. Placement of the 5/16” dowel…
This fixture is a big help when it comes to torquing the pinion nut on a 9” Ford (works on others as well). Eliminates the need for pipe wrenches, etc. and saves a lot of skinned knuckles. Made of aluminum and anodized for appearance and durability.
